单项选择题
Study the following graphic carefully Host1 and Host2， which belong to different VLANs， are in thesame subnet. According to the information displayed， which description is correct when trying toping from host to host？（）
A.A trunk port should be configured on the link between CK-SW1 and CK-SW2 to pingsuccessfully
B.The two hosts should be in the same VLAN in order to ping successfully
C.A Layer 3 device is a must in order for the ping command to be successful
D.The ping command will be successful without any further configuration changes
相关考题
-
单项选择题
Refer to the exhibit. VLAN2， VLAN3， and VLAN10 are configured on the switch D-SW1.Host computers are on VLAN 2 （10.1.2.0）， servers are on VLAN 3 （10.1.3.0）， and the management VLAN is on VLAN10 （10.1.10.0）. Hosts are able to ping each other but are unable toreach the servers. On the basis of the exhibited output， which configuration solution could rectifythe problem？（）
A.Enable IP routing on the switch D-SW1
B.Configure a default route that points toward network 200.1.1.0/24
C.Assign an IP address of 10.1.3.1/24 to VLAN3
D.Configure default gateways to IP address 10.1.2.1 on each host
E.Configure default gateways to IP address 10.1.10.1 on each host
F.Configure default gateways to IP address 200.1.1.2 on each host -
单项选择题
Refer to the exhibit. Host A and Host B are connected to the Catalyst 3550 switch and have beenassigned to their respective VLANs. The rest of the 3550 configuration is the default configuration.Host A is able to ping its default gateway， 10.10.10.1， but is unable to ping Host B. Given theoutput displayed in the exhibit， which statement is true？（）
A.HSRP must be configured on SW1
B.A separate router is required to support interVLAN routing
C.Interface VLAN 10 must be configured on the SW1 switch
D.The global config command ip routing must be configured on the SW1 switch
E.VLANs 10 and 15 must be created in the VLAN database mode
F.VTP must be configured to support interVLAN routing -
多项选择题
Youworkasanetworktechnician.YourbossisinterestedintheQoStechnologyinthecontextofvideotraffic.Whatcanbesaidofapplicationofthistechnologyinthistypeofnetwork？（）
A.The access layer is the initial point at which traffic enters the network. Traffic is marked （orremarked） at Layers 2 and 3 by the access switch as it enters the network， or is "trusted" that it isentering the network with the appropriate tag
B.No traffic marking occurs at the core layer. Layer 2/3 QoS tags are trusted from distributionlayer switches and used to prioritize and queue the traffic as it traverses the core
C.Traffic inbound from the access layer to the distribution layer can be trusted or reset dependingupon the ability of the access layer switches. Priority access into the core is provided based onLayer 3 QoS tags
D.IP precedence， DSCP， QoS group， IP address， and ingress interface are Layer 2 characteristics that are set by the access layer as it passes traffic to the distribution layer. Thedistribution layer， once it has made a switching decision to the core layer， strips these off
E.MAC address， Multiprotocol Label Switching （MPLS）； the ATM cell loss priority （CLP） bit， theFrame Relay discard eligible （DE） bit， and ingress interface are established by the voicesubmodule （distribution layer） as traffic passes to the core layer
F.The distribution layer inspects a frame to see if it has exceeded a predefined rate of trafficwithin a certain time frame， which is typically a fixed number internal to the switch. If a frame isdetermined to be in excess of the predefined rate limit， the CoS value can be marked up in a waythat results in the packet being dropped
