多项选择题
In a customer’s network， VLAN Trunking Protocol （VTP） is running with a domain named main1. VLANs 1，2，3，4，5，10，20 are active on the network. Suddenly the whole network goes down. No traffic is being passed on VLANs 2，3，4，5，10，20， however traffic passes on VLAN 1 and indicates all switches are operational. Right before the network problem occurred， a switch named TEST1 was added to the network.
What three configuration issues on TEST1 could be causing the network outage？（）
A.TEST1 is configured as a VTP server with a different domain name.
B.TEST1 is not configured to participate in VTP.
C.TEST1 is configured as a VTP server with the domain name main1.
D.TEST1 has a lower VTP configuration revision than the current VTP revision.
E.TEST1 has a higher VTP configuration revision than the current VTP revision.
F.TEST1 is configured with only VLAN1.
相关考题
-
判断题
- DS1（ Distribute switch 1） is the primary device for Vlan 101， 102， 105 - DS2 （ Distribute switch 2） is the primary device for Vlan 103 and 104 -
判断题
VLAN Trunk Protocol （VTP） reduces administration in a switched network. When you configure a new VLAN on one VTP server， the VLAN is distributed through all switches in the domain. This reduces the need to configure the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst series products. There is a Lab（about VTP） in the cisco CCNP BCMSN 642-812 exam. Requirements： These are your specifc tasks： 1. Configure the VTP information with the distribution layer switch as the VTP server 2. Configure the VTP information with the access layer switch as a VTP client 3. Configure VLANs on the distribution layer switch 4. Configure inter-VLAN routing on the distribution layer switch 5. Specific VLAN port assignments will be made as users are added to the access layer switches in the future. 6. All VLANs and VTP configurations are to completed in the global configuration To configure the switch Click on the host icon that is connected to the switch be way of a serial console cable. -
判断题
Spanning-Tree Protocol is a link management protocol that provides path redundancy while preventing undesirable loops in the network. For an Ethernet network to function properly， only one active path can exist between two stations. Multiple active paths between stations cause loops in the network. If a loop exists in the network topology， the potential exists for duplication of messages. When loops occur， some switches see stations appear on both sides of the switch. This condition confuses the forwarding algorithm and allows duplicate frames to be forwarded. To provide path redundancy， Spanning-Tree Protocol defines a tree that spans all switches in an extended network. Spanning-Tree Protocol forces certain redundant data paths into a standby （blocked） state. If one network segment in the Spanning-Tree Protocol becomes unreachable， or if Spanning-Tree Protocol costs change， the spanning-tree algorithm reconfigures the spanning-tree topology and reestablishes the link by activating the standby path. Spanning-Tree Protocol operation is transparent to end stations， which are unaware whether they are connected to a single LAN segment or a switched LAN of multiple segments.There is a lab about STP in Cisco CCNP 642-812 / 642- 892 exam. Requirements: You will configure FastEthernet ports 0/12 through 0/24 for users who belong to VLAN 20. Also, all VLAN and VTP configurations are to be completed in global configuration mode as VLAN database mode is being deprecated by Cisco. You are required to accomplish the following tasks: 1. Ensure the switch does not participate in VTP but forwards VTP advertisements received on trunk ports. 2. Ensure all non-trunking interfaces (Fa0/1 to Fa0/24) transition immediately to the forwarding state of Spanning-Tree. 3. Ensure all FastEthernet interfaces are in a permanent non-trunking mode. 4. Place FastEthernet interfaces 0/12 through 0/24 in VLAN 20
